How do you use a Meanwell power supply?
Connecting the DC Output Voltage w/ Screw Terminals Connect your Mean Well power supply’s output ground wire to one side of the terminal block. Connect the output voltage’s wire to another screw terminal. Connect your load wires to the other side of the Mean Well output voltage.
How do I connect to Meanwell driver?
Take the 3-core cable, and connect each cable to the correct matching connection. The Brown cable should be wired to the L connection, and the Blue cable to the N connection. Finally, the Green/Yellow connects to the Symbol connection.
How do you adjust the voltage on a Meanwell driver?
Adjusting A-Type Drivers Step 1: Remove the small rubber cap covering the “Io” adjustment knob. Step 2: Use the Philips screwdriver to turn the internal knob. This will adjust the output current of the driver.
How do you ground a switching power supply?
You ground the device by connecting a grounding cable to earth ground and then attaching it to the grounding point on the DC power supply. You must provide the grounding cables. The cable lug used on the grounding cable should have a #10 stud hole and accommodate a minimum of 12-AWG wire.
What does a Meanwell driver do?
Meanwell LED drivers can handle almost all of your LED needs. Starting with the PCD-16, a 16 WATT constant current LED driver, Meanwell has drivers that go up to 320 WATTs, LED drivers with dimmers and DCDC constant current drivers, as well as regular constant current drivers.
Does a DIN rail carry power?
A DIN rail power supply is a switched-mode power supply that converts unstabilised input voltage into regulated output voltage. Switched-mode power supplies are characterised by their significantly higher efficiency and lower weight as well as a more compact design than linearly regulated power supplies (transformers).
How do you dim a Meanwell driver?
To dim B-Type drivers by applying resistance, you can use a 100K potentiometer. Atreum Lighting offers an encased dimmer module (External Dimmer with Knob). Attach the dimmer by connecting the positive and negative leads to the respective leads on the LED driver.
How do I dim my LED driver?
One of the simplest and most affordable solutions to dim with the LED drivers is to use a simple 100k Ohm potentiometer. This is a variable resistor that easily attaches to the dimming wires for a cost-effective solution.
Should AC and DC grounds be connected?
Depending on the application, you can choose between a single ground point that ties all AC and DC voltages together, or separate grounds for the AC and DC voltages. In creating a common ground, you typically would connect the incoming AC voltage ground with the negative leg of the DC voltage.
Does DC voltage need a ground?
Circuits powered by batteries do not have an earth ground. Batteries do not have have a connection to the physical earth. So most DC-powered circuits, especially by batteries, have a floating ground, not an earth.
Are Meanwell drivers dimmable?
The MEAN WELL HLG ‘B’ / ‘AB’ and ELG ‘B’ / ‘AB’ series led drivers, feature Mean Well’s 3-in-1 dimming function. This means that they can be controlled with a 1-10V signal, PWM signal or with simple resistance.
Where are Meanwell drivers made?
With 2,800 employees located at its global headquarters in New Taipei Industrial Park, Taiwan, branches and sales offices at Guangzhou, Shenzhen, Suzhou in China, California USA, and Netherlands in the EU, four production bases in New Taipei City (Taiwan), Huadu District in Guangzhou, Suzhou City in China, and …
What does DIN stand for in DIN rail?
Deutsche Institut fur Normung
History of the DIN Rail Instead, DIN stands for Deutsche Institut fur Normung, which translates loosely as “German Institute for Standards.” DIN is a German organization that establishes standards for industrial and electrical equipment.
How do you ground DIN rail?
Secure the DIN rail to the backplate with the screws and washers included with the DIN rail. If a ground wire is included, slide the eyelet on one end of the ground wire over one of the mounting screws prior to securing the DIN rail. The other end of the ground wire is secured to the enclosure ground terminal.