How do I reset my South Seas spa?
Remove the spa cover and allow water to cool. Once the heater has cooled, reset by pushing any button. If spa does not reset, shut off the power to the spa and call your dealer or service organization.
What does Dr mean on South Seas spa?
Hydrotherapy Daily Stress Relief
South Seas Spas – Owner’s Manual Spa – Hydrotherapy Daily Stress Relief.
How many gallons is my South Seas spa?
360 gal.
This spa has six seats that offer a variety of jet configurations for every taste….Model 748B.
| Seating Capacity | 7 |
|---|---|
| Jets | 48 |
| Lounge Seat | No |
| Water Volume | 360 gal. |
| Size | 84 x 84 x 36in. |
How long does a hot tub take to heat up?
three to eight hours
Typically, water heats up by five to ten degrees Fahrenheit in an hour. Heating your hot tub to the desired temperature in the 100 to 102 degrees Fahrenheit range can take three to eight hours.
What do the buttons on my hot tub do?
Some larger hot tubs may have up to three jet buttons on the control panel that allow you to adjust the speed and strength of your jets. In most cases, pushing the button the first time will turn them on a low setting and pushing it again will increase the speed.
What does HFL mean on my hot tub?
The “HFL” error normally indicates a substantial difference between the sensors in your unit, and is normally caused by a water flow issue. Fixing the error codes should only take a few minutes. Before doing anything else to your hot tub, check the circuit breaker and ensure that the unit has power.
What does Flo on a hot tub mean?
A flow error on your hot tub is a sign that there is an issue with your water flowing through your heater in the hot tub. You can identify a flow error as it will display “FLO” on the front panel. Some common issues that can cause a flow error are: Lower than normal water levels. Damaged and/or dirty filter.
What does SLP mean on a hot tub?
Sleep mode
Sleep mode is displayed as SL or SLP on your topside control. ECONOMY mode heats the spa water during filter cycles only. For example if your spa is set for 100 degrees it will heat until the water temperature reaches 100 as long as the filter cycle is running.
What is SL mode on hot tub?
SL: Sleep – Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.
What do the buttons on my hot tub mean?
How do you fix a HFL code on a hot tub?
Just replace or clean the filter cartridges and the problem should be solved.
What power supply do I need for my South Seas spa?
South Seas Spas邃｢ are preset at the factory to run on 240 V, 60 Hz with a 40 A input. This feature provides for the best performance of the spa. This will require a 240 V, 50 A Class A GFCI protected service. The single pump spa may also be setup to run on 120 V, 60 Hz with a 16/40 A input.
What is the warranty on a South Seas spa?
LIFETIME STRUCTURE WARRANTY South Seas Spas邃｢ carry a lifetime structure warranty. The structure is defined as the fiberglass vessel below the exposed material finish. The manufacturer warrants the spa against loss of water due to a defect in the spa structure, for the lifetime of the spa.
Can I change the filter on my South Seas spa?
Spas邃｢ approved filter can cause issues with the circulation system and heater and can void warranty coverage. The filter can be upgraded to a 75 Sq. ft. filter. Please see your South Seas Spas邃｢ dealer, Part # 06-007-12 (standard) or 06-008-12 (Nature2) option. WARNING: Power to the spa must be turned off prior to removing the filters.
What is the pH level in a South Seas class spa?
You should maintain a slightly alkaline pH level, between 7.2 South Seas Class Spas carry a liftetime structure warranty. The struc- and 7.8, in the hydrotherapy spa. Severe problems can occur when the ture is defined as the fiberglass vessel below the exposed material fin- pH balance is not maintained within this range.