Should I use nails or screws for fascia?
Hometime.com recommends using screws instead of nails when replacing fascia to avoid jarring the existing framing with hammering.
Does fascia go on before gutters?
Before installing gutters, you should first place the fascia board, followed by the soffit. After those two components are successfully in place, you can tackle the gutter installation. You can opt for several kinds of materials and styles for your fascia, soffit, and gutters.
What screws to use for fascia?
Product Details
- The Type 316 stainless-steel fascia screw is driven through the predrilled and counterbored fascia material and securely into the substrate material.
- Additional space around the shank of the fascia screw allows for the expansion and contraction of the fascia board.
Can you put fascia over existing wood?
While it is certainly feasible to install vinyl fascia and soffit over wood, you need to ensure that you are keeping in line with the local building codes. Make sure that your attic has enough ventilation before affixing your vinyl soffit over the plywood.
Should you face nail fascia?
Never face nail fascia. *Keep nails lined up with soffit V-grooves for best appearance. Nail every 24″, but do not nail too tight. Nails should penetrate a minimum of 3/4″ into nailing surface.
Can you replace fascia without removing gutters?
There is no way to replace the fascia board without removing the gutters, as the gutters are mounted to the board. So, your roofers will carefully remove the gutters. Typically, the same gutters can be re-installed on the new fascia board, if they are in good condition.
Should fascia be face nailed?
What kind of nails should I use for fascia?
Galvanized, aluminum or stainless-steel nails are the best nails you can use for outdoor constructions like the wood soffit. Also, those nails can use for any kind of outdoor construction, installation, and repairing stuff as well.
Should you cap fascia?
Capping over is a cheaper roofline repair option as the methods used are less substantial. It should only be considered if the existing timber fascia is in very good condition and free from rot. Attaching a PVC fascia board to rotten timber may cost you more in the long run!
Should drip edge be tight against fascia?
A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.
How do you attach fascia board to drip edge?
Use 1-2 nails through each rafter to secure your fascia board. Hold the board in place, and use 2 in (5.1 cm) nails and a hammer to secure it in place. Place your nails in line with the marks on your drip edge and place it in the center of your fascia board. Drive 1-2 nails in per rafter so it doesn’t move around.
How do you attach fascia to rafters?
Drive 1–2 more nails into the fascia board at each of the rafters. Place the first nail in each rafter so they’re 1–2 inches (2.5–5.1 cm) from the top edge of the boards. Place the second nail in the rafter so it’s 3–4 inches (7.6–10.2 cm) lower than the first one so it’s held securely.
How do you nail down fascia board?
Use carpentry nails that are at least 2–3 inches (5.1–7.6 cm) long so the board stays firmly in place. Start your first nail 1–2 inches (2.5–5.1 cm) from the top of the fascia board and pound it straight through into the end of the rafter. Repeat the process on the other end of the fascia board so it’s held firmly in place.
Where can I buy fascia boards?
You can buy boards for your fascia from a hardware or home improvement store. Woods made from pine, spruce, or cedar all work well for fascia board. You may not be able to buy boards that are the exact length of your roof. If not, then get as many boards as you need to match the length.