Are Apollo ball valves directional?
Two piece threaded end Apollo Ball valves are bi-directional. They may be installed in vertical or horizontal pipe runs without regard to flow direction and without regard to stem orientation. Note: Valves must be installed in piping systems that comply with the applicable portions of the ASME B31 standards.
Is conbraco Apollo?
Over 80 years later, Conbraco is an American success story that’s still being written. The company now known as Apollo® Valves earned a reputation for developing new products to meet emerging market demands.
Where are Apollo valves made?
By “Apollo” Valves. January 3, 2019 “Apollo’s” commercial and industrial valves are designed, engineered, cast, machined, assembled, and tested in our state-of-the-art facilities in the Carolinas, right down to our yellow handles. In fact, we’ve been American-made from the very beginning.
Who owns Apollo valve?
Aalberts integrated piping systems
Apollo Valves, part of Aalberts integrated piping systems Apollo Valves is part of the stocklisted company Aalberts. Since the inception in 1975, Aalberts is where technology matters and real progress can be made – humanly, financially and environmentally.
Does it matter which direction a ball valve is installed?
VALVE ORIENTATION: Ball valves may be installed in vertical or horizontal pipe runs, they are bi-directional therefore flow direction is not critical, however the best practice is to set up the valve handle to point in the direction of flow whenever possible.
Can a ball valve be installed upside down?
Gate valves can be mounted in different orientations around the pipe line, but the preferred orientation is the stem placed vertical. It is not recommended to install upside down. The performance of a valve is dependent on proper mounting.
What does an Apollo valve do?
An alternative to adding a tank, (sometimes property owners object or there’s insufficient space,) is a thermal expansion relief valve. Available in push-fit variants, these act as a safety device, relieving the pressure if it becomes dangerously high.
What does CWP mean on a ball valve?
Cold working pressure
Cold working pressure (CWP) indicates the valve’s maximum pressure rating at temperatures between -20°F to 100°F. This is commonly referenced alongside the valve’s pressure rating. For example, 720 CWP indicates the valve is rated to 720 PSI within the CWP temperature range.
Are Apollo ball valves good?
Apollo ball valves are backed by over 80 years of experience. That amount of time includes a good deal of effort invested in producing the finest quality valves and related parts, through research, innovation, and hard work.
What ball valves are made in USA?
EVSCO is a manufacturer of plastic manual ball valves made of FDA-approved polypropylene and PVDF. Comprises of less than 50 employees, EVSCO is committed to design innovation, quality control, and customer care by developing products that improve the flow pattern and reduce operational costs.
How do you adjust Apollo valves?
To adjust the Apollo “MVA” Series, simply turn the handle to the desired setting. Facing top of the valve, turn the handle clockwise to decrease the mixed temperature, or counter-clockwise to increase the mixed temperature. Allow the mixed temperature to stabilize (at least one minute) before making another adjustment.
Do ball valves reduce water pressure?
To answer your question; A ball valve only controls flow not pressure. A few seconds after water is flowing a ball valve will limit the pressure based on the flow. A pressure regulator requires no more plumbing than a ball valve. A regulator will limit the maximum pressure but not flow until the set point is reached.
What does PN stand for in valves?
nominal pressure
Nominal diameter (DN) and nominal pressure (PN)
Does a ball valve restrict water flow?
The center of the ball has a hole — when the hole and pipe are aligned, fluid can flow. Turn the handle 90 degrees and the flow is shut off, hence the reason ball valves are classified as quarter-turn valves. If the hole through the ball is smaller than the bore of the pipe, it restricts the flow.
Where are Sharpe valves manufactured?
Northlake, Illinois
Sharpe Valve assembles all of their valves in their Northlake, Illinois headquarters. Sharpe can custom make or modify their valves to meet many of our customer’s special needs.