How do I reset my Eaton Fuller UltraShift transmission?
Note: You may use a PC-based service tool, such as ServiceRanger, to clear fault codes.
- Place shift lever in neutral.
- Set parking brake.
- Turn key on with engine off.
- Turn key off and on 6 times within 5 seconds ending with key on.
- Turn the key off and allow the system to power.
What does CA mean on Eaton Fuller transmission?
a clutch abuse event
“CA” will appear in the gear display if a clutch abuse event is occurring. “AN” will appear in the gear display if the transmission goes into Auto Neutral.
What does CA mean on dashboard?
CA (Cab-to-Axle) The distance from the back of the truck cab to the center of the rear axle. Clear or effective CA is the distance from the rear surface of any obstruction behind the cab to the center of the rear axle.
What is an 18-speed Ultra Shift?
UltraShift PLUS VXP is an 18-speed automated manual transmission designed for the heaviest heavy-duty applications – logging, mining, military and agriculture. With an unlimited maximum gross combination weight rating, it is truly a workhorse.
What is a clutch Abuse event?
Excessive torque loading often occurs during driveline ‘clutch abuse’ events, where the clutch is suddenly engaged and a transient power wave is transmitted across the driveline. This work details the development and validation of a numerical tool, which can be used to simulate such abuse scenarios.
What is the difference between UltraShift and AutoShift?
Auto shift has a clutch, and then uses the computer and solenoids to do the shifting. Ultrashift doesn’t have a clutch in the cab.
Is an UltraShift an automatic transmission?
The UltraShift 10-speed allows drivers to use the transmission in full automatic mode or with manual intervention, depending on conditions or driver preference. A Manual mode holds the current gear and allows driver-selected up-shifts or down-shifts.
What would cause the letters CA to flash on the gear display of an Eaton UltraShift?
“CA” will appear in the gear display if a clutch abuse event is occurring. “AN” will appear in the gear display if the transmission goes into Auto Neutral.
How do I check my Eaton UltraShift code?
Turn the key OFF and ON four times within five seconds ending with the key in the ON position. After five seconds, the gear display begins flashing two-digit fault codes. If no codes are active, the gear display will flash code 25 (no codes).
How do you calibrate an Eaton UltraShift clutch?
Select the “Clear Clutch Data” button to clear data from transmission controller. If successful proceed to next step, if unsuccessful exit function and re-enter. Contact Roadranger Call Center 1-800-826-4357 for help. Select the “Calibrate Clutch” button to calibrate new cultch and then Select “Finish” when complete.
What does CA mean on automatic transmission?
What does F mean on a Eaton transmission?
Active fault code
Flashing “F” in Gear Display Indicates that the transmission has detected an Active fault code. This fault code can be accessed with the ServiceRanger diagnostic software.
What is code 88 on Eaton autoshift?
Note: The gear display may flash a “88” at key on, which is a normal power-up test of the display.
What is Eaton UltraShift?
Eaton Corp. has introduced the Eaton Fuller UltraShift 10-speed, a fully automated heavy-duty truck transmission that provides North American fleets with fully automatic, two-pedal operation.
How do you adjust a Eaton clutch?
adjust the clutch. Push pedal and hold pedal down when adjusting. Push and turn adjusting nut. Turning the adjusting nut clockwise moves the bearing toward the transmission.
How do I reset my transmission?
After turning on the car, you must shift through automatic transmission gear at least two times. In manual cars, shifting between drive and reverse should occur three times. The gear shifting must continue for at least 10 miles, automatically reset the transmission control module.
What is an Eaton ultrashift transmission?
Correspondingly, what is Eaton UltraShift? It’s the same basic transmission — a 10-speed based on Eaton’s tried-and-true B-ratio mechanical box — but the clutch pedal has disappeared. The new UltraShift is available with four torque capacities from 1050 to 1650 lb ft.
What is x y sensor on Eaton ultrashift?
The X-Y Rail Position Sensor reports lateral movement of the Shift Finger to the Transmission Electronic Control Unit (TECU) as a voltage signal. Correspondingly, what is Eaton UltraShift?
What does the ultrashift plus button do?
Warning: UltraShift PLUSinitiates upshifts from MANUAL and LOW for engine over speed protection. Some engines do not use the engine overspeed protection.
Why does the fuller advantage® automated transmission upshift?
† The transmission system will upshift if necessary to prevent engine over-speed in Drive, MANUAL and LOW modes. CAUTION:The Fuller Advantage®Automated Transmission initiates upshifts from MANUAL and LOW for engine over speed protection.